Quick answer
Fog genuinely trapped inside sealed double- or triple-pane glass usually warrants an assessment for an insulating-glass problem—not an automatic whole-window replacement. Glass-only replacement may be suitable when the surrounding sash and frame remain sound and the window can accept a replacement unit. Damaged components or recurring water intrusion require a broader assessment. First confirm where the moisture sits, then check the warranty before authorizing work. (andersenwindows.com)
1. First, establish which glass surface is foggy
“Inside the window” can mean the room-facing surface or the inaccessible space between sealed panes. Those are different problems.
Room-side condensation: Moisture that wipes off the indoor glass is surface condensation. Andersen explains that this happens when moist indoor air meets sufficiently cool glass; it does not, by itself, establish that the insulating-glass seal has failed. Investigate indoor moisture and ventilation before buying replacement glass. (helpcenter.andersenwindows.com)
Outdoor condensation: Dew or haze on the exterior surface can also occur without glass failure. It forms when the outside glass temperature falls below the outdoor dew point and often evaporates as conditions change. (helpcenter.andersenwindows.com)
Between-pane moisture: Condensation within a sealed glazing cavity is a sign of a seal problem. Photograph it when visible and arrange an assessment. (andersenwindows.com)
For a practical first check, gently wipe an accessible patch of indoor glass with a clean, dry cloth. Check the exterior only where you can reach safely; do not lean out or climb to diagnose fog.
If neither accessible surface explains the haze, describe it as apparently between the panes when booking service. Not every internal film is water: glass manufacturer Cardinal documents chemical fogging that can resemble condensation but does not dissipate. A photograph alone cannot reliably establish the cause. (cardinalcorp.com)
2. Understand what each replacement option includes
Ask contractors to name the component they propose replacing. “Replace the window” is not a sufficiently precise scope.
| Option | What it means | What to establish first |
|---|---|---|
| Insulating glass unit, or IGU | Replace the sealed, multi-pane glass assembly while retaining surrounding components | Whether the sash, frame and glass-retaining area are sound and suitable for replacement glazing |
| Sash replacement | Replace the glass and the sash that holds it | Whether a compatible replacement is available and the retained frame is suitable |
| Insert replacement window | Install a replacement assembly within the retained existing frame | Whether keeping that frame is appropriate |
| Full-frame replacement | Remove the existing window and frame back to the rough opening | What frame, opening, flashing and finishing work is necessary |
Casco’s replacement-glass guidance identifies sound surrounding components as an important condition for glass-only replacement. The Department of Energy’s Building America resources separately describe sash replacement and complete window-and-frame replacement. These are distinct approaches, not interchangeable names for the same job. (cascoonline.com)
An insert is not simply a new IGU. It is also not equivalent to removing the old frame and addressing the opening. Ask explicitly what remains in place and what becomes accessible for inspection. (basc.pnnl.gov)
3. Assess the sash, frame and water history separately
Do not let visible fog become the only item on the inspection list.
Before the appointment, record whether the window opens, closes and locks normally. Note visible deterioration, loose components, staining, peeling finishes and any history of rain-related leaks. Difficulty closing can indicate a need for adjustment; it is not automatically proof that the whole window needs replacement. (andersenwindows.com)
Ask the assessor to distinguish three questions:
- Is the problem confined to the glazing?
- Can the sash and frame reliably support the proposed repair?
- Is water entering elsewhere around the window or wall?
Water staining deserves investigation, but it does not identify a leak’s source by itself. Building America guidance notes that staining can result from leakage or condensation, and that water appearing near a window can originate outside the window system. (basc.pnnl.gov)
For recurring leaks, request a water-path diagnosis rather than a promise that new glass will solve everything. Full-frame work may be appropriate where the frame or opening needs attention, but the proposed scope should explain how it addresses the identified problem. (basc.pnnl.gov)
4. Check warranty coverage before altering the glass
Gather the manufacturer’s name, product identification or serial number, purchase records and photographs. Marvin’s claims process, for example, asks owners to contact the supplying retailer and provide the product serial number. (marvin.com)
Find the warranty applicable to your product and purchase date, rather than assuming today’s document covers an older installation.
As a specific example—not a universal promise—Marvin’s warranty effective January 12, 2026 covers certain manufacturing-related insulating-glass seal failures that obstruct vision, subject to its terms. It excludes removal, installation, finishing and disposal costs. Its stated applicability is to specified products purchased on or after its effective date. (marvin.com)
Ask the warranty administrator:
- Is the reported condition covered?
- What replacement component or other remedy is authorized?
- Who may carry out the work?
- Which costs remain payable by the homeowner?
- What warranty applies afterward?
Do not assume “covered glass” means a free installed repair. Andersen’s published 400 Series and 200 Series warranty also lists replacement labor and removal/disposal among excluded costs. (andersenwindows.com)
Avoid drilling, applying treatments or approving third-party modifications before receiving warranty guidance. Alteration-related exclusions may matter. (marvin.com)
5. Match the glazing specification—not just the opening size
A quote that says only “new double-pane glass” leaves important questions unanswered.
Ask the supplier to identify:
- Glass-unit dimensions and overall thickness.
- Pane configuration and glass types.
- Low-emissivity, or low-E, coating.
- Gas fill and spacer specification.
- Tint, obscure finish and between-glass grille pattern.
- Any required tempered, laminated, safety or impact specification.
- Expected appearance beside adjacent windows.
Casco’s ordering guidance identifies thickness, coating match, appearance, spacer, grilles and safety-glass requirements among the details to confirm. Have the supplier take responsibility for the final specification and measurements rather than ordering from a homeowner’s rough measurements. (cascoonline.com)
Also distinguish glass performance from whole-window performance. DOE advises comparing whole-unit U-factors and solar heat gain coefficients rather than center-of-glass values. A glass-only performance figure should not be presented as the rating of your complete repaired window. (energy.gov)
If an exact match is unavailable, ask what will differ and request written approval of the substitute before ordering.
6. Treat defogging as a different service from IGU replacement
A service that clears haze is not necessarily restoring the original sealed-glass system.
InterNACHI’s technical guidance explains that removing moisture from a compromised glazing cavity does not fix the failed seal itself. It also cautions that a visibly clearer unit may not gain additional insulation from the treatment. That distinction matters when a proposal promises to “restore” a fogged window. (nachi.org)
Before considering a defogging service, ask:
- Is the promised result improved appearance or restored thermal performance?
- What evidence supports any insulation or gas-fill claim?
- Does the guarantee cover recurring fog, and for how long?
- What happens if staining remains?
- Does the original manufacturer approve the treatment?
Do not treat clear glass afterward as proof that the original insulating performance has returned. Cosmetic improvement and replacement of a failed sealed unit are different outcomes. (nachi.org)
This is not a recommendation to drill glass yourself. Obtain a professional assessment and check warranty implications first.
7. Work through three contrasting decision examples
These examples illustrate how to compare scopes. They are not diagnoses, reported projects or price estimates.
Example A: Fogged glass, otherwise sound window
Suppose an assessor confirms internal condensation and finds the sash, frame and glass-retaining area suitable for replacement glazing.
The next step is to request an IGU-replacement proposal specifying the glass package and installation warranty. Ask any contractor recommending a whole replacement to identify the additional defect or objective that justifies it. Sound surrounding components are the relevant starting point for considering glass-only work. (cascoonline.com)
Example B: Fogged glass and a damaged sash
Suppose the sash holding the glass is also deteriorated, but the retained frame is assessed as serviceable.
A glass-only proposal leaves the sash problem unresolved unless it includes a suitable repair. Ask whether a compatible replacement sash is available and what assessment supports retaining the frame. Sash replacement is a recognized option, but Building America guidance still calls for inspection and evaluation before proceeding. (basc.pnnl.gov)
Example C: Fogged glass and recurring rain-related staining
Suppose the glass is cloudy and stains reappear below the opening after storms.
Do not assume the two symptoms share one cause. Request investigation of the water-entry path and a written explanation of the necessary repairs. The appropriate work could extend beyond the glass or window; Building America specifically warns that apparent window leakage may originate elsewhere. (basc.pnnl.gov)
The decision principle is simple: choose a scope that addresses the confirmed defects, rather than either the smallest or largest proposal automatically.
8. Compare complete quotes and check the finished work
For a U.S. project, request written totals in U.S. dollars (USD). Compare the same opening, glazing specification and repair objective—not just the headline price.
A useful quote should state:
- Exactly which components are replaced and retained.
- Product or glass specifications and approved substitutions.
- Labor, access equipment, removal and disposal.
- Trim, painting, staining and other finishing.
- Any investigation or repair of water intrusion.
- Exclusions and the approval process for concealed damage.
- Product and workmanship warranty terms.
Treat this as a comparison checklist, not a claim that every project needs every item. Ask bidders to mark items “included,” “excluded” or “not applicable.”
For full-frame work, request particular clarity about the opening and water-management details. DOE’s window-replacement checklist distinguishes retaining an existing frame from full-frame replacement that addresses flashing and air sealing around the opening. (basc.pnnl.gov)
At completion, compare the paperwork with the approved specification, inspect the accessible glass and finishes, and confirm normal operation and locking where applicable. Keep the invoice, product identifiers, warranty documents and before-and-after photographs together.
Bottom line: Confirm where the fog sits, check coverage, and have the surrounding window assessed. Between-pane fog warrants attention, but it is not, on its own, a reason to authorize a whole-house window project. (andersenwindows.com)